Intelligence DisruptMining Disrupt Buy ticketsTickets

Antminer setup: S21 and S19, from unboxing to first hash

To set up an Antminer, connect it to a 220–277 V circuit and Ethernet, find its IP address with Bitmain's IP Reporter, log in at that address (default root / root), change the password, enter up to three pool addresses, and save. Hashrate shows on the pool within minutes. This guide follows Bitmain's own user guides for the S21 family, lists the error codes Bitmain documents with their fixes, and shows the electricity price below which each S19 still pays for its power.

Published November 20, 2026. Steps and specs are Bitmain's; the break-even table updates with every site build from live network data.

Before you start

  • Power. The S21, S21 Pro and S21 XP take 220–277 V AC, single phase, 20 A; the S19 family 200–240 V. Plug into an earthed outlet on a dedicated circuit. See how to mine at home for circuit sizing.
  • Network. A wired Ethernet connection (RJ45, 10/100M) to a router.
  • A Windows computer for Bitmain's IP Reporter tool.
  • A pool account and its stratum address, plus your worker name.
  • Upright. Bitmain says laying the unit flat increases the failure rate.

Setup, step by step

  1. Connect the power cord to the PDU and an earthed outlet, and plug in Ethernet. Do not plug or unplug anything while it is powered.
  2. Download IP Reporter from Bitmain support, extract it, and run IPReporter.exe as Administrator. Choose Default and click Start.
  3. Hold the IP Report button on the control panel until it beeps (about five seconds). The miner's IP address appears on your computer.
  4. Open that IP address in a browser and log in with Bitmain's default username root and password root.
  5. Change the password under System > Password.
  6. Under Settings, enter up to three pools: the mining address (stratum URL), your worker name, and a password if the pool asks for one. Pool 1 has priority. Save.
  7. Check the status page: a green chip icon and green LED mean it is hashing; red means a fault (see the error codes below). The pool dashboard shows your hashrate within minutes.

To set a static IP instead, enter the IP, subnet mask, gateway and DNS under Protocol and save.

Updating firmware

Download firmware only from Bitmain's support download page. In System > Firmware Upgrade, leave Keep settings ticked, choose the file and click Update, then reboot. Keep the miner powered throughout: Bitmain says a unit that loses power mid-update has to go back for repair. Recent S21 units run Secure Boot, which only accepts Bitmain-signed firmware.

Where to run it

S21S21 Pro / S21 XPS19 family
Operating temperature0–45 °C−20–45 °C0–40 °C
Humidity10–90% RH, non-condensing10–90% RH, non-condensing10–90% RH, non-condensing
AltitudeUp to 2,000 mUp to 2,000 mUp to 2,000 m
Noise76 dBA76 dBANot published

Above 900 m, Bitmain lowers the maximum operating temperature by 1 °C for every extra 300 m. It also advises keeping units away from salt air, heavy pollution and high-voltage equipment, and checking for dust monthly.

Error codes and fixes

ProblemCodeCause (Bitmain)Fix (Bitmain)
Fan errorF1:1, F2:1, F4:1, F8:1A fan is missing or slow; the miner cuts hashboard powerCheck the fan cable, swap in a known-good fan, then the PSU or control board
Hashboard missingJ:8Fewer hashboards detected than designedCheck hashboard cables and connections, or replace the board
Missing chipsJ1:2 to J8:2A chain reports fewer chips than designedCheck the chain connection, update firmware, test another PSU, check grounding
Too hotP:1High-temperature protection; hashrate drops to zeroCheck room temperature, airflow and the hashboard's thermal gel
Too coldP:2Low-temperature protectionRaise the room temperature
Power supplyV:1 to V:4Power start-up, calibration, over-spec or voltage errorReseat the PSU cable, update firmware, check wiring, then replace the PSU
PIC / EEPROMJ1:4/5 to J8:4/5Chain controller or EEPROM data errorCheck the signal cable, update firmware, try another control board
Network or poolN:4Connection lost or pool unreachableCheck the pool URL spelling, ping the pool, check cables and router

Is the S19 still worth running?

Break-even power price = (hashprice × TH/s) ÷ (watts × 24 ÷ 1,000). Today's hashprice is about $0.0279 per TH/s per day (difficulty 134.82 T, bitcoin $59,399). Below each break-even price a machine covers its electricity; it still has to cover pool fees, hosting, cooling and wear.

ModelTH/sWattsJ/THRevenue/dayBreak-even per kWh
Antminer S19 95T953,25034.2$2.653.4¢
Antminer S19 Pro 110T1103,25029.5$3.073.9¢
Antminer S19j Pro 104T1043,06829.5$2.903.9¢
Antminer S19j Pro+ 120T1203,30027.5$3.344.2¢
Antminer S19 XP 141T1413,031.521.5$3.935.4¢
Antminer S21 200T2003,50017.5$5.576.6¢
Antminer S21 Pro 234T2343,51015.0$6.527.7¢
Antminer S21 XP 270T2703,64513.5$7.538.6¢

The US average home rate was 18.16¢ per kWh in August 2026 (EIA), so an S19 only pays on industrial or stranded power. Compare every model live on aPanel, and see the cost to mine one bitcoin.

Bitmain, its distributors and repair centers exhibit at Mining Disrupt 2027 in Dallas, March 22–24.

Questions

What is the Antminer default login?
Bitmain's documented default is username root and password root. Change it right away under System > Password.
How do I find my Antminer's IP address?
Run Bitmain's IP Reporter on a Windows computer as Administrator, click Start, then hold the IP Report button on the miner for about five seconds until it beeps. The IP address appears on the computer.
How many pools can I set on an Antminer?
Three. Pool 1 has priority; the miner uses pool 2 or 3 only when the pools above are offline.
What voltage does an Antminer need?
The S21, S21 Pro and S21 XP take 220–277 V AC at 20 A; the S19 family takes 200–240 V AC. The wrong voltage can damage the unit.
Why is my Antminer hashrate zero?
Bitmain lists five causes: high-temperature protection, a failed fan, a power supply fault, a network or pool error, or a hashboard fault. The error codes below point to which one.
What happens if power fails during a firmware update?
Bitmain says the unit must then go back to it for repair, so keep it powered for the whole update.
How do I factory-reset an Antminer?
Hold the Reset button for ten seconds. The red LED then flashes once every 15 seconds.
Is the S19 still worth running in 2026?
Only on very cheap power. At November 2026 hashprice an S19j Pro breaks even at about 4 cents per kWh and an S19 XP at about 6 cents, before pool and hosting fees. The live figures are in the table on this page.

More guides

Sources

  1. Bitmain, S21 User Guide V1.2.5 · 2025-03
  2. Bitmain, S21 XP installation guide · 2024-07
  3. Bitmain, S21 specification · 2026-11-20
  4. Bitmain, S21 Pro specification · 2026-11-20
  5. Bitmain, S21 XP specification · 2026-11-20
  6. Bitmain, solution for zero hashrate · 2026-11-20
  7. Bitmain, kernel log problems and fixes · 2026-11-20
  8. Bitmain, S19 / S19 Pro specifications · 2026-11-20
  9. Bitmain, S19j Pro specification · 2026-11-20
  10. Bitmain, S19j Pro+ specification · 2026-11-20
  11. Bitmain, S19 XP specification · 2026-11-20
  12. Bitmain, firmware downloads · 2026-11-20
  13. mempool.space, difficulty and price · 2026-11-20

Three days. One floor. The whole industry.

March 22–24, 2027 · Irving Convention Center · Dallas

Mining Disrupt 2027Dallas · Mar 22–24Passes from $199Get tickets